Return to Home Page

Return to Home Page
Click the image to return to the Home Page

Sunday 9 May 2010

Building a bonsai bench


Building a bonsai bench
©Jerry Norbury, June 2009


Please Note: 
This article is published here with the kind permission of Jerry Norbury.  The copyright remains with him and I ask that you respect his intellectual property rights and ask for his permission if you want to copy or publish any of the text or images in this article.




Jerry Norbury Bonsai Bench Plans Page 1


Introduction
After thirty years working with bonsai I decided enough was enough – I needed one or more benches to display my ever growing collection of bonsai. It took me a further three years to finally get round to building the bench. It's the first large woodworking project I've ever undertaken which didn't originate from an Ikea flat-pack - and I'm really happy how well it turned out.

The basic design is built around the use of “standard” sized hardwood decking planks supported by a simple frame of treated pine. The deck planks are 215cm x 14cm x 2cm (7’ x 5.5” x ¾”). The rest of the framework is essentially sized around these dimensions. If you have different wood sizes you would need to design the overall sizes around your standard component dimensions.









Jerry Norbury Bonsai Bench Plans Page 2

Component list
All the wood used for the frame is treated pine. There are two sizes used – 65mm square and 65mm x 48mm.
The planks used for the shelves are hardwood decking (Bankirai).
Length (cm)  Quantity     Description
208                  3                Horizontal beams (65mm x 65mm)
110                  6                Back and middle legs (65) – the long legs…
82                    3                Front legs (65) – the short legs.
20                    3                Top cross beam (65)
35                    3                lower cross beam (65mm x 45mm)
10                   21              Stainless steel bolts (100mm x 8 mm)
208                  2               back and front lateral beams (45mm)
89                    4               Horizontal leg support beams (45mm thick)
8                    16               Stainless steel bolts (80mm x 8mm)
215                10               Hardwood planks (215cm x 14 cm x 2cm) – uncut
                      40-ish         Stainless steel wood screws for attaching the decking to the frame.

Additionally you need the following tools:
 A saw – unless the wood is pre-cut. I used a circular saw.
 An electric drill
 A 22mm wood drill bit for sinking holes
 An 8mm drill bit
 A ratchet wrench (11mm for the bolts I used)
 A hammer for tapping the bolts through the beams.
 A workmate© for wood when drilling.
 A set square
 A spirit level
 An electric screwdriver

Jerry Norbury Bonsai Bench Plans Page 3
Assembly
The assembly sequence is as follows:
1. Cut the wood. All joints are 90 degrees.


2. Assemble the top-most frame element from 2 x 208cm beams and 3x 20cm pieces. The centre support does not need to be exactly in the middle – but the centre legs DO need to be exactly in the middle. Sink the holes with a 22mm drill – to hide the bolt heads. Drill through the long beams with an 8mm drill – do not drill the short pieces; it’s unnecessary. Use 100mm bolts for all the 65mm square wood. Tap the bolts through the beams with the hammer into ends of the 20cm cross beams. Then use the wrench to screw the pieces together.


Jerry Norbury Bonsai Bench Plans Page 4


3. Attach the 6 long legs (do not tighten the bolts fully – the legs need to be able to turn to allow the drilling of some holes later..). The legs go exactly in the corners and exactly in the middle. The photo also shows how the ends of the top frame element appear after assembly. Note: The holes need to be offset at the corners since there are two bolts which essentially cross each other at 90 degrees – one simply needs to be closer to the end of the beam than the other and then there’s no problem.


4. Complete all the long legs the same way. Use the workmate to hold the frame during assembly. Do not fully tighten the bolts yet…

Jerry Norbury Bonsai Bench Plans Page 5


5. Using one of the short front legs, mark out on the back side of the front legs where a sink hole must be drilled . The hole will be used to attach the second level to the long legs. Theoretically the position of this hole is the length of the front leg plus half the width of the support beam which will be on top of the leg (82cm + half of 6.5cm from the bottom of the front leg). Twist the front legs (the reason the legs were not tightened earlier) and drill through all three front long legs from the back.

6. Attach the front 3 short legs under the last remaining 208cm beam. Ensure that the centre leg is exactly in the middle of the beam. The beam goes on top of the legs.

7. Attach the 3 x 35cm support members at the corners and the middle of the beam to create an inverted “L” shape. This is unstable and needs to be held in the workmate. Again you have bolts crossing each other at 90degree in the corners and in the middle and will need to be offset. The middle leg and middle support must be EXACTLY in the middle of the beam – otherwise they won’t align with the legs on the taller frame.

Jerry Norbury Bonsai Bench Plans Page 6


8. Attach the short front assembly to the long legs using the holes previously drilled through the long legs. The main frame is now complete. Unstable as yet. Go inside when it rains…


9. Making the lowest shelf supports. Measure a point on the back long legs 50cm off the ground. We will attach the back support beam (208cm x 65mmx 48mm) here. This photo shows the back beam attached AND the first front to back support. We use the shorter bolts now because the wood is not as thick. Get the main frame level (paper under the legs etc ) and then attach the back support beam to the left back leg – clamp the beam into place (level) and bolt in the right leg – then bolt in the middle back leg to the beam. We go through the beam INTO the leg this time.



Jerry Norbury Bonsai Bench Plans Page 7

10. Attach the 4 front to back supports (89cm) on the side of the legs. They need to be perfectly level.

11. Finally attach the front beam. The frame is now complete. Tighten ALL the bolts.



Jerry Norbury Bonsai Bench Plans Page 8


12. Start screwing the decking onto the frame. Add these two first and paint them with wood oil (later they are harder to get to). Paint whole frame now with wood oil and leave to dry.

13. Add the other shelves (three on top – no gap between, three in the middle with small gaps and two on the bottom with a small gap between) and screw into place (avoiding the corners where the bolt heads are!). The front of the deck hangs over the frame by roughly 4cm at the front and at the sides. The top level also hangs over the back of the frame by roughly 4cm. In my design I was initially aiming to have only 2 planks on the top – but that resulted in a big gap and no overhangs – which wasn’t attractive. I then went to three planks and no gaps.


Jerry Norbury Bonsai Bench Plans Page 9


14. Oil the planks.


15. Stand round looking happy.



Jerry Norbury Bonsai Bench Plans Page 10


16. Try it out.